SKU: KGTP75 Categories: ,
Share this product


Flex CodeTorque
Tip dia.
±0.002” (±0.05mm)
Butt dia.
±0.005” (±0.12mm)
Butt par.
±5cpm (205g Tip weight)
Balance point Kick pointMaterials
D502.7°.335” (8.50mm)3.00″.626” (15.90mm)6.00″46.00″75g300cpm54.00%MidKevlar, 40T, 30T, 3K Fiber
D402.9°.335” (8.50mm)3.00″.622” (15.80mm)6.00″46.00″75g280cpm54.00%MidKevlar, 40T, 30T, 3K Fiber
D303.1°.335” (8.50mm)3.00″.618” (15.70mm)6.00″46.00″73g265cpm54.00%MidKevlar, 40T, 30T, 3K Fiber

CPM Parameters:

Shaft typeTip weightClamp lengthClamp pressure
Driver205g4.50”4kg cm²


Flex CodeEI Profile (Butt)EI Profile (Mid)EI Profile (Tip)Kick PointBalance Profile (Counterbalanced)Balance Profile (Neutral)LaunchSpinTrajectoryTempo FitAngle Of Attack Fit (+ AoA)Angle Of Attack Fit (Neutral AoA)Angle Of Attack Fit (- AoA)Recovery ModeFlex-Fit Club Head Speed of Driver (Playing Length Avg 45-46.00”)Installation (Butt Cut)Installation (Tip Cut)
D50StiffFirm+StiffMidLowLowLowMid-Up TempoStable/Strong125-155X
D40StiffFirm+StiffMidLowLowLowMid-Up TempoStable/Strong115-125X
D30StiffFirm+StiffMidLowLowLowMid-Up TempoStable/Strong105-115X

Elastically Tailored Composites

Wound for an explosive transfer of kinetic energy….
however you drive it, KINETIXX® IMRT will optimize down range distance and target performance.

An active shaft that increases in frequency the greater the force applied.

This hard kicking, elastically tailored composite is engineered to improve club forgiveness and

generate outrageous ball speed and precise shot control!


Filament wound Vacuum Cured Construction technology produces round, pre-loaded concentric and spineless golf shafts for incomparable stability, dynamic response and feedback.

Kevlar Green Ballistic Tour series is Designed for strong players, desiring optimum control and a lower more penetrating Ballistic shot trajectory.

Tension tailored for torsional recovery and attenuation of vibration, for the purest kinetic energy transfer from shaft to clubhead.

PADERSON® KINETIXX® loaded kevlar BALLISTIC series features the worlds only continuous fiber filament wound kevlar construction technology.

Optimizing the extraordinary material properties of Kevlar to create shafts with an incredibly high tensile strength-to-weight ratio; 5x stronger than steel, with 20x the elastic strength.

KGTP75-D is a Mid Balance, Mid kick point advanced composite shaft pre-loaded with a visible fiber structural grid Engineered according to each flex, for balanced strength and stability from butt to tip, without compromising feel, producing Ballistic trajectory.

Installation Guidelines

Installation Guidelines PADERSON KINETIXX LOADED shafts:

Installation should only be completed by a qualified, trained club builder.

  1. All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
  2. Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
  3. Please do not Chamfer the tips however light belt abrasion is recommended.
    *Tip preparation: light belt abrasion or hand sanding recommended prior to final assembly.
    *To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will in many assemblies be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to insure a full shaft insert and adequate epoxy adhesion. Do not Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.


There are no reviews yet.

Be the first to review “BALLISTIC TP”

Your email address will not be published. Required fields are marked *

two × 5 =

Solve : *
8 + 7 =