VELOCITY LD

$299.00

Clear
SKU: KVMT70 Categories: ,
Share this product

Description

SPEC DECK
Flex CodeTorque
±0.5°
Tip dia.
±0.002” (±0.05mm)
Tip/par
±0.5″
Butt dia.
±0.005” (±0.12mm)
Butt par.
±0.5″
LengthWeight
±2g
Frequency
±5cpm
Balance pointKick pointMaterials
(205g Tip weight)
LD704.5°.335” (8.50mm)4.00″.638” (16.20mm)9.50”48.00”72g295cpm55.00%HighAmorphous, 40T, 30T,5T
LD60+4.5°.335” (8.50mm)4.00″.638” (16.20mm)9.50”48.00”71g275cpm54.00%HighAmorphous, 40T, 30T,5T
LD505.5°.335” (8.50mm)4.00″.630” (16.00mm)9.50”48.00”66g265cpm53.00%HighAmorphous, 30T, 5T
LD30+5.7°.335” (8.50mm)4.00″.622” (15.80mm)9.50”48.00”61g245cpm52.00%HighAmorphous, 30T, 5T
LD205.9°.335” (8.50mm)4.00″.618” (15.70mm)9.50”48.00”58g225cpm51.00%HighAmorphous, 30T, 5T

CPM Parameters:

Shaft typeTip weightClamp lengthClamp pressure
Long Drive205g4.50”4kg cm²

Fitting

Flex CodeEI Profile (Butt)EI Profile (Mid)EI Profile (Tip)Kick PointBalance Profile (Counterbalanced)Balance Profile (Neutral)LaunchSpinTrajectoryTempo FitAngle Of Attack Fit (+ AoA)Angle Of Attack Fit (Neutral AoA)Angle Of Attack Fit (- AoA)Recovery ModeFlex-Fit Club Head Speed of Driver (Based off Playing Length Avg 47.00”)Installation (Butt Cut)Installation (Tip Cut)
LD70firmfirm+firmhighmidlowmidslow-mid-upActive142+ mphX
LD60+firmfirm+firmhighmidlowmidslow-mid-upActive135+ mphX
LD50mediumfirmmediumhighmid-highlow-midmid-highslow-mid-upActive130+ mphX
LD30+mediumfirmmediumhighmid-highlow-midmid-highslow-mid-upActive115+ mphX
LD20mediumfirmmediumhighmid-highlow-midmid-highslow-mid-upActive105+ mphX
VACUUM CURED AMORPHOUS VELOCITY SERIES LONG DRIVE SHAFT MODEL#KVMT70-GRNLD

Elastically Tailored Composites
PURE KINETIC ENERGY
The confluence of materials and craftsmanship

Technology/Design

Featuring Dual-flex reactive technology, in the worlds only pre-loaded and vacuum cured Nano-Carbon amorphous fiber material shaft construction, table rolled laminate composite.

Vacuum Cured to minimize resin content, optimizing elastic strength and dynamic recovery properties of the Nano-Carbon Amorphous material. Enhancing feedback and delivering an extremely forgiving shaft.

Active butt and tip quadrants tailored for high speed long drive athletes desiring to improve efficiency and increase ball velocity, through the purest kinetic energy transfer from golfer to club.

KVMT70-LD is a Mid-High Balance point, High kick point advanced composite table rolled construction, that kicks hard and recover’s fast, in tailored sequence from butt to high tip.

Producing increased ball velocity and a Medium height piercing shot trajectory.

Installation Guidelines

Installation Guidelines PADERSON KINETIXX LOADED shafts:

Installation should only be completed by a qualified, trained club builder.

  1. All PADERSON KINETIXx loaded shafts are to be BUTT Cut to length only.
  2. Do not TIP trim any shaft model! Regardless of CPM, or club assembly config.
  3. Please do not Chamfer the tips however light belt abrasion is recommended.
    *Tip preparation: light belt abrasion or hand sanding recommended prior to final assembly.
    *To ensure a smooth and clean build, we perform a post-production tip preparation: 1″ Metalwoods, 1.25″ Irons. depending on hosel bore depth, there will in many assemblies be the need to lightly sand beyond the prepared surface delivered. Light belt abrasion is also recommended to insure a full shaft insert and adequate epoxy adhesion. Do not Chamfer tip section or blade prep (scratch) tip to prepare for epoxy.

Reviews

There are no reviews yet.

Be the first to review “VELOCITY LD”

Your email address will not be published. Required fields are marked *

3 × 4 =